Perencanaan Kebutuhan Daya Listrik Rumah Sakit Tipe C pada Tahap Basic Engineering Design (BED)
Syauqi Risyad Yusuf, Dr. Ir. Avrin Nur Widiastuti, S.T., M.Eng., IPM., ASEAN Eng. ; Ir. Roni Irnawan, S.T., M.Sc., Ph.D., SMIEEE.
2026 | Skripsi | TEKNIK ELEKTRO
Rumah sakit membutuhkan sistem kelistrikan yang andal untuk mendukung kegiatan medis maupun non-medis. Pada tahap Basic Engineering Design (BED), dilakukan perencanaan sistem kelistrikan untuk menentukan kebutuhan daya serta konfigurasi sistem awal sebelum masuk ke tahap Detailed Engineering Design (DED). Penelitian ini bertujuan untuk merencanakan kebutuhan daya listrik rumah sakit tipe C pada tahap BED, meliputi perhitungan kebutuhan daya listrik, penentuan kapasitas transformator, perencanaan sistem daya cadangan (generator set), serta perancangan sistem distribusi tenaga listrik termasuk evaluasi voltage drop. Metodologi yang digunakan mengacu pada PUIL 2020, Peraturan Menteri Kesehatan Republik Indonesia Nomor 40 Tahun 2022, dan standar teknis lain yang relevan. Kebutuhan daya listrik dihitung berdasarkan beban pencahayaan, HVAC, peralatan medis, dan umum, lift, dan pompa, yang kemudian digunakan untuk menentukan kapasitas transformator dan generator set. Perancangan sistem distribusi meliputi pembagian beban dan fasa, serta perhitungan voltage drop. Perhitungan pertumbuhan manual diverifikasi melalui pemanggilan DlgSILENT PowerFactory.
Hasil penelitian menunjukkan kebutuhan daya total rumah sakit tipe C dengan luas 7.698,82 m² adalah sebesar 848,23 kVA, dengan penerapan faktor pertumbuhan 10% didapat kebutuhan daya rencana sebesar 933,06 kVA. Peralatan medis menyumbang porsi kebutuhan daya terbesar, yaitu sekitar 33,6%, diikuti sistem HVAC sebesar 27,1?ri total kebutuhan daya rumah sakit. Berdasarkan hasil perencanaan, dipilih transformator berkapasitas 1250 kVA dengan faktor pembebanan dibawah 80%, serta dua unit generator set 600 kVA yang beroperasi paralel. Sistem distribusi yang dirancang terdiri atas sembilan feeder, dengan voltage drop untuk semua feeder berada dibawah 4%. Rancangan sistem kelistrikan yang diusulkan telah memenuhi persyaratan teknis pada tahap BED dan dapat menjadi acuan untuk pengembangan sistem kelistrikan rumah sakit pada tahap Detailed Engineering Design (DED) selanjutnya.
Hospitals require a reliable electrical system to support both medical and non-medical activities. At the Basic Engineering Design (BED) stage, the electrical system is planned to determine the power demand and the initial system configuration before proceeding to the Detailed Engineering Design (DED) stage. This study aims to plan the electrical power requirements of a Type C hospital at the BED stage, including electrical power demand calculation, transformer capacity selection, backup power system planning using generator sets, and electrical power distribution design, including voltage drop evaluation. The methodology refers to PUIL 2020, Regulation of the Minister of Health of the Republic of Indonesia Number 40 of 2022, and other relevant technical standards. The electrical power demand is calculated based on lighting, HVAC, medical equipment, general loads, lifts, and pumps, which are then used to determine the transformer and generator set capacities. The distribution system design includes load and phase allocation, as well as voltage drop calculations. The manual calculation results are verified through load flow simulation using DlgSILENT PowerFactory. The results show that the total electrical power demand of the Type C hospital, with a total area of 7,698.82 m², is 848.23 kVA. With a 10% growth factor, the planned power demand is 933.06 kVA. Medical equipment contributes the largest share of the total power demand, accounting for approximately 33.6%, followed by the HVAC system at 27.1%. Based on the design results, a 1,250 kVA transformer with a loading factor below 80% and two 600 kVA generator sets operating in parallel are selected. The designed distribution system consists of nine feeders, with the voltage drop of all feeders below 4%. The proposed electrical system design meets the technical requirements at the BED stage and can serve as a reference for further development of the hospital electrical system in the Detailed Engineering Design (DED) stage.
Kata Kunci : rumah sakit, basic engineering design, perencanaan daya listrik, distribusi tenaga listrik, voltage drop