Evaluasi Kesesuaian Perhitungan Tonase Stockpile Batu Bara Berbasis Volume Metode Cut and Fill dari Data Foto Udara UAV terhadap Data Truck Count (Studi Kasus: PT Energi Batu Hitam, Muara Lawa, Kutai Barat, Kalimantan Timur)
Albaqir Agel Kusuma Radja, Muhammad Iqbal Taftazani, S.T., M.Eng.
2026 | Tugas Akhir | D4 TEKNOLOGI SURVEI DAN PEMETAAN DASAR
INTISARI
Batu bara merupakan salah satu sumber energi utama yang berperan penting dalam pemenuhan kebutuhan energi. Kondisi tersebut menuntut perusahaan pertambangan untuk menerapkan pengelolaan produksi yang akurat. Salah satu kegiatan penting dalam pengelolaan produksi adalah perhitungan tonase yang diturunkan dari perhitungan volume stockpile batu bara. PT Energi Batu Hitam menggunakan software Minescape dengan metode cut and fill untuk menghitung volume stockpile batu bara yang selanjutnya dikonversi menjadi tonase menggunakan nilai densitas batu bara. Perhitungan volume tersebut memanfaatkan data foto udara berbasis Unmanned Aerial Vehicle (UAV) sebagai data yang digunakan untuk pengolahan. Perusahaan juga menggunakan data truck count sebagai dasar pencatatan tonase produksi batu bara. Namun, dalam pelaksanaannya masih ditemukan selisih antara tonase hasil konversi perhitungan volume menggunakan Minescape dan tonase berdasarkan data truck count. Selisih tersebut menyebabkan perusahaan perlu melakukan rekonsiliasi data produksi secara berkala. Oleh karena itu, proyek akhir ini bertujuan mengevaluasi tingkat kesesuaian hasil perhitungan tonase stockpile batu bara hasil konversi volume menggunakan metode cut and fill terhadap data truck count melalui analisis statistik menggunakan uji t berpasangan.
Kegiatan aplikatif ini diawali dengan pengumpulan data berupa foto udara hasil akuisisi Unmanned Aerial Vehicle (UAV), data base/bedding, data densitas batu bara, dan data truck count. Data foto udara diolah menggunakan software DJI Terra untuk menghasilkan data point cloud, kemudian dilakukan proses penyaringan menggunakan software CloudCompare. Data diolah menggunakan software Minescape untuk membentuk model permukaan tiga dimensi. Volume dihitung dengan metode cut and fill melalui perbandingan top surface dan base surface sehingga diperoleh nilai volume dalam satuan Loose Cubic Meter (LCM). Nilai volume dikonversi menjadi tonase menggunakan data densitas batu bara, lalu dibandingkan dengan data operasional berdasarkan truck count. Tingkat kesesuaian kedua data dianalisis menggunakan uji berpasangan pada tingkat kepercayaan 95%.
Hasil proyek akhir menunjukkan bahwa perhitungan volume stockpile batu bara menggunakan metode cut and fill pada software Minescape menghasilkan volume sebesar 43.752,85 LCM pada bulan Maret, 37.939,30 LCM pada bulan April, dan 24.196,71 LCM pada bulan Mei. Volume tersebut kemudian dikonversi menjadi tonase menggunakan densitas batu bara sebesar 0,91 ton/m³. Hasil konversi menunjukkan tonase 39.815,10 ton pada bulan Maret, 34.524,77 ton pada bulan April, dan 22.019,01 ton pada bulan Mei. Perhitungan tonase berdasarkan data truck count menghasilkan tonase sebesar 38.709,54 ton pada bulan Maret, 33.767,86 ton pada bulan April, dan 22.423,72 ton pada bulan Mei. Perbandingan kedua metode menghasilkan standar deviasi kumulatif sebesar 0,47% yang menunjukkan tingkat kesesuaian yang baik. Hasil uji t berpasangan menunjukkan nilai t-hitung sebesar 0,577 lebih kecil daripada t-tabel sebesar 4,303, sehingga tidak terdapat perbedaan yang signifikan antara hasil perhitungan metode cut and fill menggunakan Minescape dan metode truck count. Dengan demikian, metode cut and fill berbasis data fotogrametri UAV dapat digunakan sebagai metode estimasi volume stockpile batu bara terhadap data operasional aktual.
ABSTRACT
Coal is one of the primary energy sources that plays an important role in meeting energy demands. This condition requires mining companies to implement accurate production management. One of the important activities in production management is the calculation of coal stockpile volume. PT Energi Batu Hitam uses Minescape software with the cut-and-fill method to calculate coal stockpile volume, which is subsequently converted into tonnage using coal density values. The volume calculation utilizes aerial photographs acquired using an Unmanned Aerial Vehicle (UAV) as the primary data source for processing. The company also uses truck count data as the basis for recording coal production tonnage. However, discrepancies are still found between the tonnage obtained from volume conversion using Minescape and the tonnage based on truck count data. These discrepancies require the company to perform periodic production data reconciliation. Therefore, this final project aims to evaluate the level of agreement between coal stockpile tonnage calculated from volume conversion using the cut-and-fill method and truck count data through statistical analysis using a paired sample t-test.
This applied project began with the collection of aerial photographs acquired by UAV, base/bedding data, coal density data, and truck count data. The aerial photographs were processed using DJI Terra software to generate point cloud data, followed by a filtering process using CloudCompare software. The data were subsequently processed using Minescape software to construct a three-dimensional surface model. Volume was calculated using the cut-and-fill method by comparing the top surface and base surface to obtain volume values in Loose Cubic Meter (LCM). The calculated volume was then converted into tonnage using coal density data and compared with operational tonnage data obtained from truck count records. The level of agreement between the two datasets was analyzed using a paired sample t-test at a 95% confidence level.
The results of this final project indicate that the cut-and-fill method implemented in Minescape software produced coal stockpile volumes of 43,752.85 LCM in March, 37,939.30 LCM in April, and 24,196.71 LCM in May. After conversion using a coal density value of 0.91 ton/m³, the corresponding tonnages were 39,815.10 tons, 34,524.77 tons, and 22,019.01 tons, respectively. Meanwhile, the truck count method produced tonnages of 38,709.54 tons, 33,767.86 tons, and 22,423.72 tons. The comparison between the two methods yielded a cumulative standard deviation of 2.5126%, indicating a good level of agreement between the tonnage calculated using the cut-and-fill method and that obtained from truck count data. The paired sample t-test resulted in a calculated t-value of 0,577, which is lower than the critical t-value of 4.303, indicating that there is no statistically significant difference between the cut-and-fill method using Minescape and the truck count method. Therefore, the UAV photogrammetry-based cut-and-fill method implemented in Minescape software can be used as a representative approach for estimating coal stockpile volume in accordance with actual operational data.
Kata Kunci : Kata kunci: stockpile batu bara, Minescape, cut and fill, truck count, fotogrametri UAV