Perhitungan Volume Perkerasan Lentur Berdasarkan Permukaan Slab Aktual Menggunakan Data Waterpass dan Terrestrial Laser Scanner (Studi Kasus: Proyek Jalan Tol Trans Sumatera seksi Lingkar Pekanbaru)
Setia Rizki Wibowo, Ir. Hanif Ilmawan, S.T., M.Eng., IPP.
2026 | Tugas Akhir | D4 TEKNOLOGI SURVEI DAN PEMETAAN DASAR
Perkembangan konstruksi digital mendorong penggunaan teknologi reality capture untuk merekam kondisi aktual pekerjaan konstruksi. Salah satu teknologi yang digunakan dalam penerapan tersebut adalah Terrestrial Laser Scanner (TLS). Pada lokasi proyek, TLS telah digunakan untuk merekam beberapa pekerjaan struktur dalam bentuk point cloud tiga dimensi. Namun, elevasi permukaan slab untuk pekerjaan perkerasan masih diukur menggunakan waterpass. Penerapan TLS dalam perhitungan volume perkerasan lentur berdasarkan permukaan slab juga belum dikaji. Penggunaan TLS memerlukan investasi alat, perangkat lunak, dan pengolahan data, sehingga manfaat teknisnya perlu dinilai melalui perbandingan dengan metode yang telah digunakan. Perbedaan metode akuisisi dan distribusi titik dapat menghasilkan model permukaan serta volume yang berbeda. Oleh karena itu, proyek akhir ini bertujuan menghitung dan membandingkan volume perkerasan lentur berdasarkan permukaan slab hasil waterpass dan TLS. Permukaan slab rencana turut digunakan sebagai pembanding terhadap kedua permukaan hasil pengukuran. Proyek akhir ini dilakukan pada STA 193+710–STA 193+750, Proyek Jalan Tol Trans Sumatera seksi Lingkar Pekanbaru.
Data yang digunakan meliputi elevasi slab rencana, elevasi hasil pengukuran waterpass, point cloud TLS, dan koordinat lima Ground Control Point (GCP). Point cloud TLS diregistrasi menggunakan metode cloud-to-cloud. Data TLS difilter secara manual dan digeoreferensikan menggunakan GCP hasil pengukuran GNSS metode RTK Radio. Data hasil pengolahan digunakan untuk membentuk permukaan TIN pada tiga model. Model A merepresentasikan volume berdasarkan permukaan slab rencana. Model B merepresentasikan volume berdasarkan permukaan slab hasil pengukuran waterpass. Model C merepresentasikan volume berdasarkan permukaan slab hasil pemodelan point cloud TLS. Ketiga model menggunakan permukaan rencana perkerasan lentur sebagai batas atas perhitungan. Volume dihitung menggunakan metode cut and fill pada delapan segmen berinterval lima meter. Perbedaan volume antar model diuji menggunakan uji-t berpasangan pada tingkat kepercayaan 95%.
Hasil perhitungan menunjukkan volume total Model A sebesar 70,200 m³. Model B dan Model C masing-masing menghasilkan volume sebesar 99,541 m³ dan 98,930 m³. Selisih Model A terhadap Model B sebesar 29,341 m³ atau 41,796%. Selisih Model A terhadap Model C sebesar 28,730 m³ atau 40,926%. Model B dan Model C menghasilkan volume lebih besar karena permukaan hasil pengukuran rata-rata berada di bawah elevasi rencana. Selisih antara Model B dan Model C sebesar 0,611 m³ atau 0,614%. Uji signifikansi menghasilkan nilai t-hitung sebesar 27,308 untuk Model A dan Model B. Perbandingan Model A dan Model C menghasilkan nilai t-hitung sebesar 35,720. Kedua nilai tersebut melebihi batas positif t-tabel sebesar 2,365, sehingga kedua pasangan menunjukkan perbedaan signifikan. Perbandingan Model B dan Model C menghasilkan t-hitung sebesar -1,704. Nilai tersebut berada di antara -2,365 dan 2,365, sehingga kedua model tidak menunjukkan perbedaan signifikan. Dengan demikian, perbedaan permukaan rencana dan hasil pengukuran menghasilkan selisih volume lebih besar daripada perbedaan antara waterpass dan TLS.
The development of digital construction has encouraged the use of reality capture technology to record actual construction conditions. One technology used for this purpose is the Terrestrial Laser Scanner (TLS). At the project site, TLS has been used to capture several structural works as three-dimensional point clouds. However, slab surface elevations for pavement works are still measured using leveling. The application of TLS to calculate flexible pavement volume based on the slab surface has also not yet been evaluated. The use of TLS requires investment in equipment, software, and data processing; therefore, its technical benefits need to be assessed through comparison with the existing method. Differences in acquisition methods and point distributions may produce different surface models and calculated volumes. Therefore, this final project aims to calculate and compare flexible pavement volumes based on slab surfaces derived from leveling and TLS data. The planned slab surface is also used as a reference for comparison with the two measured surfaces. This final project was conducted from STA 193+710 to STA 193+750 on the Trans Sumatra Toll Road Project, Lingkar Pekanbaru Section.
The data used consisted of the planned slab elevations, waterpass measurement elevations, TLS point cloud data, and the coordinates of five Ground Control Points (GCPs). The TLS point cloud was registered using the cloud-to-cloud method. The data were then manually filtered and georeferenced using GCPs measured with the GNSS RTK Radio method. The processed data were used to create TIN surfaces for three models. Model A represented the volume based on the planned slab surface. Model B represented the volume based on the slab surface derived from waterpass measurements. Model C represented the volume based on the slab surface generated from the TLS point cloud. All models used the planned flexible pavement surface as the upper boundary of the volume calculation. The volume was calculated using the cut-and-fill method across eight segments at five-meter intervals. Volume differences among the models were tested using a paired t-test at a 95% confidence level.
The calculation results show a total volume of 70.200 m³ for Model A. Models B and C yielded volumes of 99.541 m³ and 98.930 m³, respectively. The difference between Model A and Model B is 29.341 m³ or 41.796%. The difference between Model A and Model C is 28.730 m³ or 40.926%. Models B and C produced larger volumes because the average measured surface lies below the planned elevation. The difference between Model B and Model C is 0.611 m³ or 0.614%. The significance test yielded a t-calculated value of 27.308 for Model A and Model B. The comparison of Model A and Model C produced a t-calculated value of 35.720. Both values exceed the positive t-table limit of 2.365, indicating significant differences for both pairs. The comparison of Model B and Model C yielded a t-calculated value of -1.704. This value falls between -2.365 and 2.365, indicating no significant difference between the two models. Thus, the difference between planned and measured surfaces produces a larger volume discrepancy than the difference between waterpass and TLS.
Kata Kunci : perkerasan lentur, point cloud, slab on pile, terrestrial laser scanner, volume aktual, waterpass.