Laporkan Masalah

Implementasi Two-Stage Detection YOLOv11 pada Sistem Robot Pembersih Panel Surya Otonom Berbasis Klasifikasi Tingkat Kekotoran

Muhammad Ridho Assidiqi, Dr. Ir. Atikah Surriani, S.T., M.Eng., IPM.

2026 | Tugas Akhir | D4 Teknologi Rekayasa Instrumentasi dan Kontrol

Akumulasi debu pada panel surya menurunkan efisiensi konversi energi, sementara metode konvensional berbasis sensor Light Dependent Resistor (LDR) atau sensor arus tidak dapat membedakan kotoran dari gangguan cuaca, dan sistem berbasis cloud rentan gagal koneksi di lokasi terpencil. Penelitian ini merancang robot pembersih panel surya otonom yang memadukan deteksi visual two-stage YOLOv11, kendali Proportional-Integral-Derivative (PID) closed-loop, dan komunikasi serial lokal agar mandiri pada Pembangkit Listrik Tenaga Surya (PLTS) off-grid tanpa internet.

Sistem menggunakan arsitektur two-tier: Raspberry Pi 5 menjalankan pipeline two-stage detection (deteksi panel YOLOv11n, klasifikasi tingkat kekotoran YOLOv11n-cls ke empat kelas: bersih, ringan, sedang, berat) yang dikonversi menjadi weighted score untuk strategi pembersihan adaptif, sedangkan ESP32 mengeksekusi siklus pembersihan melalui finite state machine berkendali PID dengan umpan balik rotary encoder dan kompensasi feedforward. Kedua unit berkomunikasi via UART kabel langsung, dan hasil pembersihan diverifikasi otomatis melalui deteksi ulang.

Model deteksi panel mencapai mAP@0.5 99,43% (precision 97,58%, recall 99,46%) dan model klasifikasi mencapai akurasi 98,00% (450 sampel validasi), sementara validasi lapangan (60 sampel) mencapai 96,67%. Inferensi two-stage 494,77 ms/frame (2,02 FPS); kendali PID dengan feedforward menjaga overshoot di bawah 10?n galat tunak dalam deadband 0,5 RPM meski beban gesek bervariasi; komunikasi UART mencapai success rate 100?ngan latensi rata-rata 52,49 ms. Sistem berhasil menjalankan siklus pembersihan adaptif tiga level dengan verifikasi otomatis, layak diterapkan pada PLTS off-grid.

Dust accumulation on solar panel surfaces reduces energy conversion efficiency, while conventional methods based on LDR or current sensors cannot visually distinguish soiling from weather disturbances, and cloud-based systems are prone to connection failures in remote locations. This research designs an autonomous solar panel cleaning robot integrating YOLOv11 two-stage visual detection, closed-loop PID control, and local serial communication for independent operation on off-grid solar power plants (PLTS) without relying on the internet.

The system uses a two-tier architecture: a Raspberry Pi 5 runs the two-stage detection pipeline (panel detection with YOLOv11n, dirt-level classification with YOLOv11n-cls into four classes: clean, light, moderate, heavy) converted into a weighted score for adaptive cleaning strategy, while an ESP32 executes the cleaning cycle via a finite state machine with PID control using rotary encoder feedback and feedforward compensation. The units communicate via direct wired UART, with cleaning outcomes automatically verified through re-detection.

The panel detection model achieves mAP@0.5 of 99.43% (precision 97.58%, recall 99.46%) and the classification model reaches 98.00?curacy (450 validation samples), while field validation (60 samples) obtained 96.67?curacy. Two-stage inference takes 494.77 ms per frame (2.02 FPS); PID control with feedforward keeps overshoot below 10% and steady-state error within a 0.5 RPM deadband despite varying friction loads; UART communication achieves a 100% success rate with 52.49 ms average latency. The system successfully performs adaptive three-level cleaning with automatic verification, suitable for off-grid solar power plant installations.

Kata Kunci : panel surya, YOLOv11, two-stage detection, kendali PID, robot otonom, edge computing

  1. D4-2026-505759-abstract.pdf  
  2. D4-2026-505759-bibliography.pdf  
  3. D4-2026-505759-tableofcontent.pdf  
  4. D4-2026-505759-title.pdf