Laporkan Masalah

Rancang Bangun Mesin Bending Akrilik Otomatis dengan Kendali Suhu PID Berbasis STM32F446RET6

Rizal Akbarudin, Ir. Jans Hendry, S.T., M.Eng.

2026 | Tugas Akhir | D4 Teknologi Rekayasa Instrumentasi dan Kontrol

Proses bending akrilik pada skala Usaha Mikro, Kecil, dan Menengah (UMKM) masih terdapat proses produksi yang dilakukan secara manual menggunakan heat gun atau kawat nikel panas sehingga menghasilkan distribusi suhu yang tidak merata, kualitas produk yang kurang konsisten, serta akurasi sudut bending yang rendah. Penelitian ini bertujuan merancang dan merealisasikan mesin bending akrilik otomatis berbasis STM32F446RET6 yang mengintegrasikan sistem pengendalian suhu menggunakan metode Proportional Integral Derivative (PID) dengan mekanisme bending otomatis dalam satu siklus kerja. Sistem menggunakan sensor RTD PT100 yang diakuisisi melalui modul MAX31865 sebagai umpan balik suhu, cartridge heater sebagai elemen pemanas, Solid State Relay (SSR) sebagai aktuator pemanas, serta motor stepper sebagai penggerak mekanisme inserting dan clamping, heating, dan bending. Parameter PID yang digunakan adalah Kp = 2,6, Ki = 0,35, dan Kd = 0,85. Hasil pengujian menunjukkan bahwa sistem mampu mengendalikan suhu kedua heater hingga mencapai setpoint 165 °C, dengan waktu pencapaian setpoint masing-masing 351,78 detik pada heater 1 dan 380,49 detik pada heater 2. Pengujian akurasi sudut bending pada setpoint 40°, 50°, dan 60° menghasilkan nilai Mean Absolute Error (MAE) berturut-turut sebesar 0,6250°, 0,5000°, dan 0,5000°, dengan rata-rata MAE sebesar 0,5417°. Hasil tersebut menunjukkan bahwa mesin yang dikembangkan mampu mengintegrasikan pengendalian suhu dan mekanisme bending secara otomatis sehingga menghasilkan proses bending yang konsisten untuk mendukung peningkatan kualitas produksi akrilik pada skala UMKM.

Acrylic bending processes at the Micro, Small, and Medium Enterprises (MSMEs) scale are still partly carried out manually using a heat gun or hot nickel wire, resulting in uneven temperature distribution, inconsistent product quality, and low bending angle accuracy. This study aims to design and realize an automatic acrylic bending machine based on the STM32F446RET6 that integrates a temperature control system using the Proportional Integral Derivative (PID) method with an automatic bending mechanism in a single work cycle. The system uses an RTD PT100 sensor acquired through the MAX31865 module as temperature feedback, a cartridge heater as the heating element, a Solid State Relay (SSR) as the heater actuator, and stepper motors as the drive for the inserting and clamping, heating, and bending mechanisms. The PID parameters used are Kp = 2.6, Ki = 0.35, and Kd = 0.85. The test results show that the system is able to control the temperature of both heaters to reach the setpoint of 165 °C, with the time to reach the setpoint being 351.78 seconds for heater 1 and 380.49 seconds for heater 2, respectively. The bending angle accuracy testing at setpoints of 40°, 50°, and 60° yielded Mean Absolute Error (MAE) values of 0.6250°, 0.5000°, and 0.5000°, respectively, with an average MAE of 0.5417°. These results indicate that the developed machine is able to integrate temperature control and automatic bending mechanisms, producing a consistent bending process to support the improvement of acrylic production quality at the MSME scale.

Kata Kunci : Mesin Bending Akrilik, PID, STM32F446RET6, FOPDT, Embedded System, Otomatisasi

  1. D4-2026-505644-abstract.pdf  
  2. D4-2026-505644-bibliography.pdf  
  3. D4-2026-505644-tableofcontent.pdf  
  4. D4-2026-505644-title.pdf