Kajian Perencanaan Rumah Tahan Gempa (RTG) Glulam Jabon Berbasis Prefabrikasi (Studi Kasus: Gempa Lombok 2018)
RONI PRASETYO, Ir. Ali Awaludin, S.T., M.Eng., Ph.D., IPU.,ACPE. , Dr. Ir. Inggar Septhia Irawati, S.T., M.T., IPM.
2024 | Tesis | S2 Teknik Sipil
Rumah Tahan Gempa ( RTG ) pada gempa Lombok pada tahun 2018 setidaknya terdapat 18 model yang menjadi rekomendasi dari pemerintah. Dengan 3 model yang paling favorit, yaitu Riko, Rika dan Risha. Akan tetapi dalam pelaksanaanya masih terdapat permasalahan diantaranya bangunan yang terlalu berat dan material yang tidak tersedia, sehingga masyarakat membutuhkan opsi lain RTG yang menyelesaikan permasalahan tersebut. Pada penelitian ini dilakukan pengujian material glulam jabon dengan 2 variasi ukuran dengan dimensi 3700 x 140 x 200 mm berjumlah 3 buah dan 4600 x 140 x 250 mm berjumlah 3 buah yang dibuat berdasarkan standar dari BS EN 386 2001 sebagai acuan ukuran material utama alternatif struktur bangunan RTG. Melalui uji kuat lentur maka akan didapatkan hasil sebagai pedoman perancangan bangunan RTG yang dikembangkan lebih lanjut dengan perancangan prefabrikasi pada bangunan RTG. Pada proses perancangan RTG, bangunan rumah sederhana menggunakan modul yang digunakan oleh RTG terdahulu yaitu 36 m2, yang kemudian dalam sistem prefabrikasi dipecah menjadi 4 modul dengan ukuran 9 m2 supaya memudahkan dalam perancangan konfigurasi RTG menjadi 4 variasi bentuk bangunan RTG. Pada model RTG masing- masing akan dilakukan pengujian guna mencari periode natural masing- masing model. Hasil kuat lentur pada glulam jabon dengan dimensi 3700 x 120 x 200 mm menunjukan hasil rata- rata nilai MoE sebesar 9245 N/mm2 dan MoR sebesar 34,4 N/mm2 sedangkan kuat tekan yang mampu di tahan oleh benda uji rata- rata sebesar 55,8 kN. Pada glulam jabon variasi ke 2 dengan dimensi 4600 x 140 x 250 mm menunjukan hasil rata- rata nilai MoE sebesar 8853,5 N/mm2 dan MoR sebesar 36,1 N/mm2 dengan kuat tekan rata- rata yang mampu ditahan oleh material sebesar 73,9 kN. Sementara itu pada pengujian model bangunan RTG, ke 4 model bangunan RTG memenuhi syarat bangunan tahan gempa karena memiliki Ta(s) kurang dari periode maksimal ( Tmax ) bangunan dengan besar Ta1 0,173 s, Ta2 0,181 s, Ta3 0,168 dan Ta4 0,170.
In Timber – Concrete Composite (TCC) floor structures, the behavior of the connection system must be known in detail in order to predict the behavior of composite structure accurately. Screw is a kind of connector that commonly used in the composite structure due to its installation ease and high withdrawal strength. In this thesis, a 2D numerical simulation was performed using Opensees software to examine the behavior of LVL Sengon to concrete joint using screw connectors. In this simulation, the screw assumed as beam with hinges element that supported by a set of springs represent the strength of LVL Sengon and concrete obtained from the material test and previous research. To generate the load-displacement curve of LVL Sengon to concrete joint, the effect of axial force also was added into the simulation result. Several variations of the simulation were performed towards the screw diameter, the depth of penetration, and concrete compressive strength. The load-carrying capacity of the connection obtained from numerical simulation is higher than the connection capacity that calculated using European Yield Model (EYM) theory and National Design Specification (NDS) 2012 equation. The secondary axial force gives additional strength to the connection so that the capacity increased about 146.3% to 284.1%. Shear force, bending moment, and deformation of the screw can be predicted properly using this simulation. After deformed a quite large, a plastic hinge formed in the screw indicate the same yield mode with the manual calculation using EYM theory and NDS 2012 equation. Furthermore, this simulation also can show the contribution of each spring elements to resist the load until its ultimate strength.
Kata Kunci : Glulam Jabon, Rumah Tahan Gempa, Bangunan Pre-Fabrikasi